how to trim a palm tree with a chainsaw

Reduction cuts shorten a branch back to a lateral branch. How to Trim a Tall Palm Tree Tall palm tree pruning using hydraulic lift with a basket.

Tree Services Sydney The Tree Doctor Palm Tree Trimming Tree Trimming Tree Trimming Service

Start the cut roughly 3 inches below the first cut.

. Make a diagonal cut below the cut. There is a process. The lateral branch then acts as the new dominant end of the branch and keeps hormonal control over unregulated growth.

Check your palm tree one more time and make sure what pruning is needed. No one should stand on the fall side of the tree. How to Remove Palm Trees With a Chainsaw Step 1.

Depending on the size of the frond pick your tool and begin low. Furthermore how do you cut a tree trunk. Use your knife or saw to cut off dead fronds starting at the base of the trees foliage.

Now I knowCLICK SHOW MOREThanks for watching. Begin cutting from the side of the trunk opposite your pie cut. If any fronds hang higher than at a ninety-degree angle dont cut these.

Palm trees grow upward. Clear a debris path by removing anything the tree could damage in the direction you want it to. Plan the Fall Direction.

Make the top cut of the hinge ensure you make it at a height that there will be plenty of room for the lower cut. The apex of the notch should go approximately 13rd into the tree. I guess the chance of a kickback is pretty slim but Ill let someone else figure those odds.

Saw the horizontal felling cut. It is possible for a palm to survive a lot of damage. Steps by Steps Guideline to Trim the Palm Tree Step 1.

Place the blade on the roots of the ball and then press down to sever it. Examine your palm tree properly. Examine the palm tree and note the direction in which it leans.

Make the Cut. Warn everyone on the property to stand well out of the way. Ive always wondered what it would be like to cut a palm tree with my chainsaw.

2 Cut off any low branches that might get in the way when pruning and dont cut higher than your shoulders. Saw a horizontal cut one-third of the way through the trunk of the palm tree on the side of the trunk facing the direction you want it to fall. Start Cutting Branches at the Trunk After felling the tree cut off branches starting at the lower end of the trunk and.

Furthermore what is the best tool to trim palm trees. Remove fronds below the angle 90 lines even if they are green. Make the lower cut.

How to cutting palm trees down 1 After clearing the area and knowing which way the tree is going to fall you can start cutting the palm tree. Cut a 70-degree open-face notch on the tree with your chainsaw on the side of the tree facing the direction you want it to fall. Go to the side of the tree and begin working your way to the back.

Work upwards cutting the fronds you. Saw upward to meet the base of the first cut and remove a wedge of the palm tree trunk with a 30-degree angle. If you cut fronds that grow at an.

If you want to cut through them use a saw hoe or shovel. 3 Either with an. Then use a regular pole saw or an electrical pole saw to trim the fronds.

Begin cutting horizontally a third of the way down from the top of your pie cut and stop cutting about half way through the trunk. Your cut should be at least 2 inches away from the trunk. If you not afraid of height you can rent a very tall ladder.

Home Depot has extension ladders that extend up to 40 ft and cost around 50 per day for rent. Click to see full answer. Before you start trimming the tree you need to examine it properly.

Make a diagonal cut below the cut. These three cuts will be used to meet any pruning objective we might have. If you do your palm will die.

You really want to focus on the fronds that are facing down or wilting. Remove the saw and make a cut on the top of. Stand clear of the tree and your helper should be able to gently pull the rope and bring the tree down.

Removal cuts remove an entire branch or clean out the center of a tree. Pruning the larger roots that are beyond the ball can be done. First thing anytime you prune you want to wipe down the blades with 70 isopropyl alcohol to sterilize your tools.

Cut 2 inches from the tree trunk. Clear the fell path and the escape routes. Place the cut 2 feet off the ground.

Beginning at least 8 inches from the tree trunk make a cut one-third of the way through the limb from the bottom. Be careful not to cut the trees crown. Get Rid of Dead Leaves.

Tree Services Tree Service Tree Lopping Tree Removal Service

Hot Topics Chainsaw Recommendations Doityourself Com Http Www Doityourself Com Stry Hot Topics Chainsaw Tree Service Tree Trimming Service Tree Removal